Silver Ionic and Colloidal FAQ
Colloidal Silver Features
Making high-quality colloidal silver is now easier than ever. The Silver Pulser comes with a custom retainer that is placed on top of your glass of water or other container. The silver wires extend straight down into the water and are held in place by a spring-loaded clip. Silver wire length is adjustable to fit the depth of your glass or container. The silver wires are easy to remove and replace. During the process of making colloidal silver, the positive silver wire loses silver and gradually shrinks in diameter. By switching the positive and negative wires around, the usable life of the wires is doubled and you can make twice the amount of colloidal silver.
|
The Silver Pulser SP-5 is the main part of Dr. Bob Beck's exerimental protocol that also includes the Magnetic Pulser and Water Ozonator. Features include a built-in Constant-Current circuit for the Ionic/Colloidal Silver output, an LED Light that indicates when the current through the stimulator electrodes is correct and a long-lasting electrode headset. The Silver Pulser is sometimes confused with Dr. Hulda Clark's Zapper but these two instruments function in different ways, operating under different principles. The Hulda Clark Zapper delivers particular Rife frequencies to the body in the range of 30 thousand cycles as its basis of operation, whereas the Silver Pulser is based upon a 1992 U.S. medical research and design patent that describes the use of voltage and current in order to neutralize the infective activity of viruses and bacteria.
Each Silver Pulser is a professionally designed quality unit, thoroughly tested on an oscilloscope, and is guaranteed to operate per the specifications. (Click HERE to see the original Bio-Protocol schematic or HERE for the improved schematic. NOTE: Our Silver Pulser has a more advanced and proprietary circuit than what is shown here.)
The Unit:
The Silver Pulser is a dual function unit 1) Bio-Stimulator and 2) Ionic/Colloidal Silver Generator with Constant-Current.
The Silver Pulser uses only the highest quality .9999 Pure Fine Silver Electrodes. Our Assay Certificate for Silver Wires is on file, and can be viewed by clicking HERE. Our Certificate of Compliance for Silver Wire Purity is on file, and can be viewed by clicking HERE.
The Silver Pulser generates the finest quality Ionic Colloidal Silver at a rate of 5-8 ppm (part per million) in 2 Hours for 16 ounces of distilled water, with an Ionic Colloid silver particle size that is mostly ions, with colloidal particles in the range of 0.005 - 0.015 microns (Verified on a Scanning Electron Microscope). The ZBB5 Model has a built-in Constant-Current Circuit for the ultimate in Ionic/Colloidal Silver Production.
To see independent lab tested results of our Ionic Colloidal Silver as an anti-bacterial solution please click HERE.
The Silver Pulser has a Bi-Phasic output frequency of ~3.92 Hertz (cycles per second) at a nominal voltage of 31 VOLTS DC peak per cycle.
Unique Features:
-
The Bio-Electric Protocol has changed. SOTA boosted the output voltage from 27 Volts to 31 Volts (from 54 Volts Peak-Peak, to 62 Volts Peak-Peak). A new intensity control was specified to help widen the band of the output control to avoid "bunching" the signal near the high end of the control knob.
-
A unique circuit design allows The Silver Pulser to operate from a single 9 Volt alkaline battery. Original plans actually called for the use of 7 batteries in the design. Our state-of-the-art electronic design utilizes a proprietary DC-DC converter which boosts the output of the 9 Volt battery to the 31 Volts DC required by The Silver Pulser.
-
Constant-Voltage Output - Unique circuitry maintains the required 31 Volts output regardless of battery voltage or other input power (like from an AC-DC Wall Adaptor, Automobile Battery, or Solar Panel). Thus, as the battery runs down or if the input voltage fluctuates, the output will maintain the 31 Volts. No other unit using either 3 x 9 Volt batteries or voltage triplers can offer this very important feature.
-
We use only the purest, Fine Silver Wire Electrodes, 4 Nine Grade (.9999 pure) for the Ionic-Colloid Silver production.
-
Constant-Current Output - ZBB5 Model has built-in Constant-Current Circuit for Ionic/Colloidal Silver production.
-
Output monitoring circuit and indicator.
-
The Bio-Stimulator Probes are of the highest quality.
-
Our Electrical Circuit Boards are GOLD Plated for extreme reliability and workmanship.
-
All electrical wire connections made with Food Grade solders and fluxes for the highest in safety and purity.
-
3 Year Parts and Labour Warranty on all internally mounted components. Replacement Fine Silver Wire Electrodes and Probes are available.
The Silver Pulser is housed in an attractive new custom plastic enclosure with a built-in compartment for the 9 Volt battery. A slide-off lid allows you to change the battery easily. A Thumbwheel Switch Control Knob turns The Silver Pulser on and off and varies the intensity of the "Bio-Stimulator Probe" output.
A Green LED Light comes on when the Silver Pulser is turned on.
A flashing Yellow LED light on the unit indicates there is a correct Bio-Stimulator output and comes on only when current is flowing.
An Orange LED light is used for the Ionic-Colloidal Silver generation. The Orange LED Light comes on only when current through Silver Wires is correct and the circuit is complete.
A Red LED Light indicates low battery.
The Silver Pulser has one 6 pin DIN style jack for plugging in the Fine Silver Wires and for the Bio-Stimulator Probes. A second jack is used for hooking up an AC-DC Wall Adaptor so you don't have to go through batteries. NOTE: You cannot power the unit with a Wall Adaptor at the same time as using the Bio-Stimulator output. This is a government regulatory stipulation. However, a Wall Adaptor can be used for Silver production only.
We include Cotton Sleeves to put over the Bio-Stimulator Probes for helping to maintain a good connection when moistened. (Hint: Use a Salt Water solution or a conductive gel for better conductivity!)
The Silver Pulser is packaged in a custom soft carrying case for easy storage.
Electronics:
The Silver Pulser is designed to the highest standards. We have improved on the design with added features. Our electronic design is unique and efficient making the unit very portable and light-weight. There's even a provision for adding an external power source to save on batteries when making Ionic/Colloidal Silver, such as an AC-DC Wall Adaptor which you can purchase from any electronic store.
Specifications:
- Battery Voltage: 9 Volts DC (Alkaline Battery)
- Optional Input Voltage: 6 - 12 Volts DC @500mA Wall Transformer/Adapter, Automobile Battery, or Solar Panel.
- Output Voltage at Colloidal Silver Wires: 31 Volts DC, (+/- 1 Volt) Constant-Voltage Output
- Output Current at Colloidal Silver Wires: 1.5 milliamps (+/- 0.5ma) Constant-Current Output
- Ionic-Colloid Silver Production: 5 - 8ppm (parts per million) for 2 hours for 16 ounces distilled water.
- Ionic-Colloid Silver Particle Size: Mostly ionic, with colloidal particles in the range of 0.005 - 0.015 microns when made as directed.
- Ionic-Colloid Silver Colour: Clear or Pale Gold.
- Silver Wire Life: Can make many gallons ionic/colloidal silver per set of Fine Silver Wires, when made as directed.
- Output Voltage at Stimulator Probes: 31 Volts (Peak per Cycle, 62 Volts Peak-Peak) Bi-Phasic at ~3.92 Hertz (cycles per second) +/- 1 Hz. To see the actual output waveform from the oscilloscope, please click HERE. Note the extremely square and symmetrical waveform; free of any spikes or artifacts.
- Output Current at Stimulator Probes: ~12 milliamps maximum when probes shorted and Control Knob on full intensity.
The Fine Silver Wires are 14 AWG (1.63mm or 0.064" dia.) x 8" long (20 cm) and are constructed of only Pure Fine (.9999 pure) Silver Wire.
Bio-Stimulator Probes are 1/8" diameter x 1.25" long (3mm diameter x 3.8 cm long).
Weight of The Silver Pulser unit is only a few ounces - very lightweight.
Each Silver Pulser comes complete with:
Colloidal Silver Features
Making high-quality colloidal silver is now easier than ever. The Silver Pulser comes with a custom retainer that is placed on top of your glass of water or other container. The silver wires extend straight down into the water and are held in place by a spring-loaded clip. Silver wire length is adjustable to fit the depth of your glass or container. The silver wires are easy to remove and replace. During the process of making colloidal silver, the positive silver wire loses silver and gradually shrinks in diameter. By switching the positive and negative wires around, the usable life of the wires is doubled and you can make twice the amount of colloidal silver.
|
CUT SHIPPING BY A DAY!
Speed delivery of your discounted SOTA products - CLICK HERE or call 1-800-224-0242 and give code: CA50026
Questions? Call or email us.
The SOTA Silver Pulser has two functions. This unit offers the benefits of gentle microcurrents of electricity and also makes Colloidal Silver.
Microcurrent stimulation helps the body's natural electricity for more energy and greater health. Ionic Colloidal Silver is one of nature's germ fighters.
If you have, or purchase, the Magnetic Pulser, the power cord from it may be used with the Silver Pulser. Alternately, you can purchase a power cord for the Silver Pulser.
|
